Stepper motor versus servo motor

Which is right for your application?

In today’s industrial marketplace, it can be challenging and confusing when choosing the correct motor for an application. As well as all the different types of motor, the information provided on each is often either too basic or too technical to be helpful. In this article, Mike Keefe of KEB America explains the differences between stepper and servo motors, and when it is appropriate to use each technology.

A stepper motor is a type of brushless DC motor. They are designed to provide a certain number of defined steps per revolution. For example, a motor with 200 steps/revolution will offer a position resolution of 1.8°/pulse (360°/200 pulses). Each time the motor is pulsed by the stepper controller, it will move in the forward or reverse direction according to the number of pulses received. In the stepper example given above, 100 pulses would cause the motor to rotate 180°. 

Advantages of stepper motors

A stepper motor is able to offer open-loop positioning, which is a big advantage, compared to open-loop induction motors, which are not able to provide positioning. Most stepper motors do not include any feedback, which lowers the overall cost of a stepper and control solution. Their low cost is a primary reason for their widespread use. One advantage in industrial applications is that a stepper motor can be run with a DC powered stepper drive. They do not require larger inverters that input 230/460VAC or bulky fusing and cabling, which can be quite significant with multi-axis applications.

Limitations of stepper motors

It is possible for a stepper to ‘lose’ position. This can happen, if the stepper motor does not provide sufficient torque to move the shaft and load. It can also happen at high speeds where the stepper motor goes too fast to lock in at each step. This could also happen, if the inertia of the load carries it past the intended step when it is stopped. If the position accuracy of the stepper is critical, some motors will add feedback, such as an incremental encoder.

The feedback will identify, if the actual shaft position deviates from the expected position and the motor can correct itself, as needed. The exception is when the load torque exceeds the rated torque of the stepper. In this case, the motor will stall and not be able to correct itself.

Steppers do not retain any sort of known positioning when they are powered down. Therefore, they need to complete a homing routine every time they are powered up. You can see this when you turn on your printer at home. You will see the motors complete a routine that resets to a known ‘home’ position. In short, stepper motors are ideal for a wide variety of industries and small power applications, ranging from 3D printers, adjustable conveyors and small metering pumps.

What is a servo motor?

While servo motors simply mean a motor controlled with feedback, in the world of automation it is accepted to specifically mean an AC permanent magnet synchronous motor. These motors have a stator similar to that of an induction motor, but their rotors are constructed with rare earth magnets. This eliminates the slip found in induction motors and allows the servo motor to run at the synchronous speed defined by the frequency and number of poles (rpm = 120*Frequency# of Poles).

Advantages of servo motors

AC servo motors use rare earth permanent magnets, so they offer best-in-class torque density. This is preferred for very dynamic motor applications that must accelerate and decelerate quickly. Servo motors include some sort of feedback, whether it is a resolver or encoder. The shaft feedback is critical, because it is used in the servo controller to control rotor position and torque.

Unlike a stepper motor, servo motors are capable of providing momentary peak torque across its speed range. A servo motor’s peak torque can be very important in certain applications and can result in an optimised motor selection. In addition, AC servo motors operate at much higher speeds, compared to stepper motors.

Critical motion control applications that involve functional safety and the handling of critical or expensive products (eg, semiconductor machines) should use servo motors with feedback. The low-cost benefit of a stepper motor/control simply does not justify the risk of injury or product failure. Common examples for their best use are in packaging machines, material handling and robotics.

KEB servo motors can be equipped with absolute encoders, which retain their position information even when the system is powered down. This can be very important in applications where re-homing is not possible.

Limitations of servo motors

The main disadvantage of servo motors, compared to stepper motors, is going to be the cost of the motor and the associated drive that controls it. This is particularly true for smaller power applications (eg, 500W and below). If the application does not require the precision and high torque overload that a servo motor offers, then a stepper motor is likely to be the better choice.

Servo motors are well suited to a range of industries and applications, such as powering conveyor systems for packaging machines, metal cutting and forming machines, as well as robotics.

What does KEB offer?

KEB offers a range of products to support both stepper and servo motors. On the stepper motor side, KEB stepper drive module offers control for stepper motors up to 5A, while utilising CiA 402 motion control profiles. KEB also offers both servo motors and drives to control them. The KEB servo motors offer speeds up to 9,000 rpm and nominal torques as high as 70Nm. To control the motors, the COMBIVERT S6 and COMBIVERT F6 drives combine flexibility and performance to make them ideal for servo applications.

Servo motors provide a high peak torque at 0 speed.
Servo motors provide a high peak torque at 0 speed.

KEB (UK) Ltd

5 Morris Close
Park Farm Industrial Estate

+44 (0)1933 402220

Individual service for signal integrity
The demands on connection technology performance are constantly increasing. By providing customised support, Phoenix Contact helps customers select connection components to ensure the highest possible signal integrity.
Aveva MES rises in the leader ranks of the latest Gartner report
Aveva’s Manufacturing Execution Systems (MES) offering, which is deployed in the UK & Ireland by AVEVA Select partners SolutionsPT, has been recognised as a global leader in industrial software in the latest 2022 Gartner Magic Quadrant for Manufacturing Execution Systems.
Siemens selected by Microsoft for RAMP Programme
Siemens Digital Industries Software has been selected to participate in the Rapid Assured Microelectronics Prototypes (RAMP) Phase II initiative.
Thomson Industries exhibits linear actuators for the marine industry
Thomson Industries will be exhibiting at the 30th Shipbuilding, Machinery and Marine Technology (SMM) trade fair in Hamburg in September, showcasing its comprehensive line of electric linear actuators for marine applications.
Harwin and MSA Components sign German distribution deal
Harwin is bringing greater strength to its German supply chain through a new strategic partnership with MSA Components. The agreement allows MSA to offer all the latest products from Harwin’s extensive portfolio.
Mould making at Emka for injection moulding of plastics and metals
Emka reports that it is now one of the top three mould makers in Europe – producing 900 moulds a year for plastic injection, including polyamide/glass and Grivery, as well as zinc and aluminium die casting.
Kontron receives VDC Research’s Gold Award for vendor satisfaction
Kontron has been recognised for outstanding customer satisfaction. The company has received the Gold Vendor Satisfaction Award for IoT and Embedded Hardware technology from VDC Research.
Mouser wins Vishay Distributor of the Year Award
Mouser Electronics has received the 2021 High Service Distributor of the Year award from Vishay Intertechnology, one of the world’s largest manufacturers of discrete semiconductors and passive electronic components.
What changes does the new machinery regulation bring?
As the machinery regulation replaces machinery directive 2006/42/EC, Dirk Meyer, specialist engineer solution architect at Eaton, looks at what is changing.
Klüber Lubrication receives Schaeffler Supplier Award 2022
Schaeffler has awarded Klüber Lubrication with the Supplier Award 2022 in the field of quality. The jury emphasised in particular the global supplier's strong commitment to the compliance with quality standards.

Login / Sign up